Trucks and Marine


for-trucks

XMT4 XM Radio Mirror Mount Truck AntennaXMT4 XM Radio Mirror Mount Truck Antenna

XMT4 Advanced No Ground Plane Antenna For XM Satellite Radio Reception. For trucks with tow-style mirrors. The XMT4 truck antenna is XM approved and quickly mounts to any vertical or horizontal tube up to 1-1/10" diameter. For optimal performance, the antenna should be mounted vertically. This extremely versatile antenna can be mounted to any other vehicles such as RV's, off-road vehicles, maritime ships, and motorcycles.

Features:

  • The Most Advanced XM Antenna Available.
  • Mounts Anywhere & Meets/Exceeds XM Spec.
  • No Ground Plane Required.
  • Weighs Only Few Ounces.
  • Can Be Used For Other Sat Radio Services (Sirius) with Limited Performance.

Kit Includes:

  • Antenna Assembly (w/ attached cable & L-bracket)
  • Indented Flat 2" Square Clamp (w/ 4 holes)
  • 4 Sets of Hex Lock-Nuts, Washers, & Bolts
  • 5 Pcs of Cable Tie Wraps

Specifications:

Electrical

  • Frequency: 2332.5 to 2345.0 MHz
  • Gain 2 dBic (20-60 deg elevation) -2 dBi (horizon)
  • Bandwidth: 12.5 MHz
  • Impedance: 50 ohms
  • Polarization LHCP (20-60 deg elevation) Linear (Horizon)

LNA

  • Gain: 30 dB, typical
  • Noise Figure: 1.0 dB, maximum
  • Power: 4.5 Vdc, nominal
  • Current Drain: 60 mA, maximum
  • Unwanted Signal Rejection: 40 dB, minimum

Cable

  • Type: Coaxial RG-174
  • Length: 16 feet
  • Connector: 90 degree SMB

Mechanical

  • Overall Height: 11.75 inches
  • Effective Diameter: 0.75-0.82 inches
  • Housing Material: Black ABS, UV Stable
  • Mounting: Horizontal or Vertical Tubing 7/16" to 1" Diameter
  • Rated Wind Velocity: 150 mph
  • Weight: 0.25 Lbs w/out Cable

Temperature

  • -40 C to +105 C, operating
  • -45 C to +120 C, storage

Quality and Performance Tests

  • XM Approved: Per Specification XM-TEC-3-0009-2-RD

This antenna is compatible all XM Satellite Receivers. NOT compatible with SKYFi car cradles with either a dual-lead connector or a pink Fakra connector.



XMT4 XM Radio Mirror Mount Truck Antenna -xm-truck-antenna-xmt4$59.99
XMT102 XM Radio Mirror Mount Truck AntennaXMT102 XM Radio Mirror Mount Truck Antenna

XMT102 Antenna For XM Satellite Radio Reception. For trucks with tow-style mirrors. The XMT102 truck antenna is XM approved and quickly mounts to any vertical or horizontal tube up to 1-1/10" diameter. For optimal performance, the antenna should be mounted vertically. This extremely versatile antenna can be mounted to any other vehicles such as RV's, off-road vehicles, maritime ships, and motorcycles.

Features:

  • The Most Advanced XM Antenna Available.
  • Mounts Anywhere & Meets/Exceeds XM Spec.
  • No Ground Plane Required.
  • Weighs Only Few Ounces.
  • Can Be Used For Other Sat Radio Services (Sirius) with Limited Performance.

Kit Includes:

  • Antenna Assembly (w/ attached cable & L-bracket)
  • Universal Aluminum 2" Square Clamp (w/ 4 holes)
  • 4 Sets of Hex Lock-Nuts, Washers, & Bolts
  • 6 Pcs of Cable Tie Wraps

Specifications:

Electrical

  • Frequency: 2332.5 to 2345.0 MHz
  • Gain 2 dBic (20-60 deg elevation) -2 dBi (horizon)
  • Bandwidth: 12.5 MHz
  • Impedance: 50 ohms
  • Polarization LHCP (20-60 deg elevation) Linear (Horizon)

LNA

  • Gain: 30 dB, typical
  • Noise Figure: 1.0 dB, maximum
  • Power: 4.5 Vdc, nominal
  • Current Drain: 60 mA, maximum
  • Unwanted Signal Rejection: 40 dB, minimum

Cable

  • Type: Coaxial RG-174
  • Length: 16 feet
  • Connector: 90 degree SMB

Mechanical

  • Overall Height: 11.75 inches
  • Effective Diameter: 0.75-0.82 inches
  • Housing Material: Black ABS, UV Stable
  • Mounting: Horizontal or Vertical Tubing 7/16" to 1" Diameter
  • Rated Wind Velocity: 150 mph
  • Weight: 0.25 Lbs w/out Cable

Temperature

  • -40 C to +105 C, operating
  • -45 C to +120 C, storage

Quality and Performance Tests

  • XM Approved: Per Specification XM-TEC-3-0009-2-RD

This antenna is compatible all XM Satellite Receivers. NOT compatible with SKYFi car cradles with either a dual-lead connector or a pink Fakra connector.



XMT102 XM Radio Mirror Mount Truck Antenna xm-truck-antenna-xmt102$59.99
XM500 XM Radio Clip Mount Truck AntennaXM500 XM Radio Clip Mount Truck Antenna

This antenna will clamp mount to the air dam shield or flap of long-haul trucks, or similar installation. This antenna can also be mounted to any flat surface able to accomodate a clamp-style mount bracket.

For best performance, the black antenna housing at the top of the mast should be installed above any other truck parts for an unobstructed view of the sky in all directions. A sample installation is shown to in this photo.

Features:

  • Ground Plane independent - no metal surface needed
  • 30 foot Heavy-gauge RG58/U low loss coaxial cable
  • Field replaceable sub-assembly components (see replacement parts)
  • Rugged antenna withstands high-vibration environment
  • High performance meets XM Satellite Radio specifications

Kit Includes:

  • Antenna Assembly (w/ attached cable)
  • Angle Bracket
  • Clamp Bracket Assembly
  • Hex Nuts & Washers
  • Pink Fakra Housing
  • 90 Degree SMB Adapter
  • 8 Pcs of Cable Tie Wraps
  • 6 Pcs of Cable Tie Mounts

This antenna is designed for single antenna lead XM Satellite Radio receivers. It may also be used with older dual antenna lead receivers with the addition purchase of an optional splitter. This antenna is NOT compatible with XM PCR, Sony PnP, or XM Boomboxes.

Installation instructions included. Not recommended for round bar mounting.



XM500 XM Radio Clip Mount Truck Antenna xm500-xm-truck-antenna$69.99Add: 
XM4 XM Radio Universal Mount Truck AntennaXM4 XM Radio Universal Mount Truck Antenna

This antenna is universally designed for trucks and RVs that employ a single arm (single antenna lead) XM Satellite Radio applications. There are several methods of clamping this antenna; Mirror Mounting, Air Dam Shield Mounting, Flap Mounting to the trucks cab and any flat surface accommodating the U-Bracket clamp style mounting.

Features:

  • Environmentally tested and validated
  • Low-profile design maximizes installation options
  • Robust Antenna Design to Withstand Long Haul Truck Vibration Environments
  • High Performance meets XM Satellite Radio Specifications

Kit Includes:

  • 1 Antenna Assemply
  • 1 Mirror Mount Clamp A
  • 1 Mirror Mount Clamp B
  • 4 M6XP1.0 Hex Screws
  • 4 M6 Washers
  • 4 M6 Lock Washers
  • 4 M6XP1.0 Hex Nuts
  • 1 3/4 Ext. Tooth Lock Washer
  • 1 3/4-16 Hex Nut
  • 1 U-Bracket Assembly
  • 1 Air Dam Shield Clamp D
  • 1 3/8-16 Hex Nut
  • 1 3/8 Split Lock Washer
  • 1 21 Foot RG-174/U Low-Loss Coaxial Cable with Right Angle SMB Connector
  • Illustated Mounting Instructions

Specifications:

Electrical

  • Frequency: 2332.5 to 2345.0 MHz
  • Bandwidth: 12.5 MHz
  • Impedance: 50 ohms

LNA

  • Gain: 30 dB, typical
  • Noise Figure: 0.9 dB, maximum

Cable

  • Type: Coaxial RG-174
  • Length: 21 feet
  • Connector: 90 degree SMB

Mechanical

  • Overall Height: 10 inches
  • Effective Diameter: 0.75-0.82 inches
  • Diameter: 3.75"
  • Weight: 0.88 Lbs w/out Cable

Temperature

  • -40 C to +185 C, operating
  • -45 C to +120 C, storage

This antenna is compatible all XM Satellite Receivers. NOT compatible with SKYFi car cradles with either a dual-lead connector or a pink Fakra connector. MyRadioStore also has a 25' Replacement Cable available.



XM4 XM Radio Universal Mount Truck Antenna xm-truck-antenna-universal-mount-xm4$64.99
SR-3653 XM Radio Clamp or Mirror Mount Truck AntennaSR-3653 XM Radio Clamp or Mirror Mount Truck Antenna

This antenna is designed for long-haul trucks that employ a single arm (single antenna lead) XM Satellite Radio applications. There are several methods of clamping this antenna to the long-haul truck; Mirror Mounting, Air Dam Shield Mounting, Flap Mounting to the trucks cab and any flat surface accommodating the U-Bracket clamp style mounting.

Features:

  • Aerodynamic Antenna Assemply Design
  • Ground Plane Independent Design
  • Field Replaceable Sub-Assembly Components
  • Robust Antenna Design to Withstand Long Haul Truck Vibration Environments
  • High Performance meets XM Satellite Radio Specifications

Kit Includes:

  • 1 Antenna Assemply
  • 1 Mirror Mount Clamp A
  • 1 Mirror Mount Clamp B
  • 4 M6XP1.0 Hex Screws
  • 4 M6 Washers
  • 4 M6 Lock Washers
  • 4 M6XP1.0 Hex Nuts
  • 1 3/4 Ext. Tooth Lock Washer
  • 1 3/4-16 Hex Nut
  • 1 U-Bracket Assembly
  • 1 Air Dam Shield Clamp D
  • 1 3/8-16 Hex Nut
  • 1 3/8 Split Lock Washer
  • 1 21 Foot RG-174/U Low-Loss Coaxial Cable with 90 degree SMB Connector

Specifications:

Electrical

  • Frequency: 2332.5 to 2345.0 MHz
  • Bandwidth: 12.5 MHz
  • Impedance: 50 ohms

LNA

  • Gain: 30 dB, typical
  • Noise Figure: 0.9 dB, maximum

Cable

  • Type: Coaxial RG-174
  • Length: 21 feet
  • Connector: 90 degree SMB

Mechanical Specifications

  • Overall Height: 10 inches
  • Effective Diameter: 0.75-0.82 inches
  • Diameter: 3.75"
  • Weight: 0.88 Lbs w/out Cable

Temperature

  • -40 C to +185 C, operating
  • -45 C to +120 C, storage

This antenna is compatible all XM Satellite Receivers. NOT compatible with SKYFi car cradles with either a dual-lead connector or a pink Fakra connector. MyRadioStore also has a 25' Replacement Cable available.



SR-3653 XM Radio Clamp or Mirror Mount Truck Antenna xm-truck-antenna-mirror-mount-sr-3653$69.99
2315 XM Radio Mirror Mount Truck Antenna2315 XM Radio Mirror Mount Truck Antenna

The Tram 2315 truck antenna quickly mounts to any vertical or horizontal tube up to 1-1/10" diameter. Perfect for trucks with tow-style mirrors. For optimal performance, the antenna should be mounted vertically. This extremely versatile antenna can also be mounted to other vehicles such as RV's, off-road vehicles, maritime ships, and motorcycles.

Features:

  • Compatible with all XM Radios that feature an SMB antenna connection
  • Compact, sleek design
  • 3-Way stainless steel mount
  • Hermetically sealed antenna
  • Gold plated right-angle SMB antenna connection
  • 10-Ft heavy-duty think RG-174 coaxial cable

Specifications:

  • Frequency: 2332.5 to 2345.0 Mhz
  • Satellite gain: 5dBic typical
  • Terrestrial gain: -1dBic typical
  • Noise figure: 1.0 dB max
  • Current consumption: 45mA typical 55mA max.
  • Supply voltage: 4.7 volts typical
  • Operating temperature: -40*F to 220*F
  • Antenna height: 10 inches

This antenna is compatible all XM Satellite Receivers. It is NOT compatible with SKYFi car cradles with either a dual-lead connector or a pink Fakra connector.



2315 XM Radio Mirror Mount Truck Antenna tram-2315$39.99
BRX30 XM Mirror Mount 30 Inch Truck AntennaBRX30 XM Mirror Mount 30 Inch Truck Antenna

The Browning BRX30 truck antenna features a 30 inch mast, giving your antenna the height it needs to attain the strongest signal. It quickly mounts to any vertical or horizontal tube up to 1-1/10" diameter. This extremely versatile antenna can also be mounted to other vehicles such as RV's, off-road vehicles, maritime ships. Its heavy duty design is built to withstand use in high winds and high vibration areas.

Features:

  • Compatible with all XM Radios that feature SMB antenna connections
  • 30 inch heavy duty, sleek design
  • 3-Way stainless steel mount
  • Right-angle SMB antenna connection
  • 17-Ft heavy-duty think RG-174 coaxial cable

Specifications:

  • Frequency: 2332.5 to 2345.0 Mhz
  • Satellite gain: 5dBic typical
  • Terrestrial gain: -1dBic typical
  • Noise figure: 1.0 dB max
  • Current consumption: 45mA typical 55mA max.
  • Supply voltage: 4.7 volts typical
  • Operating temperature: -40*F to 220*F

This antenna is compatible all XM Satellite Receivers. It is NOT compatible with SKYFi car cradles with either a dual-lead connector or a pink Fakra connector.



BRX30 XM Mirror Mount 30 Inch Truck Antenna brx30$59.99
MSTRSAT Universal XM/Sirius Mirror Mount Truck AntennaMSTRSAT Universal XM/Sirius Mirror Mount Truck Antenna

This universal satellite radio antenna with will with both XM and Sirius satellite radio receivers. Ending the need to have two antenna on your vehicle if you listen to both Satellite radio companies or change from one to the other. The antenna quickly mounts to any vertical or horizontal tube up to 1-1/10" diameter. For optimal performance, the antenna should be mounted vertically. This extremely versatile antenna can be mounted to any other vehicles such as RV's, off-road vehicles, maritime ships, and motorcycles.

Features:

  • Universal Design Works with All Satellite Radio Services
  • Stainless Steel Mirror Mount
  • 21' Military Specification RF-58U Cable with Gold Plated Connectors
  • Antenna cable disconnects for easy installation

Includes:

  • Antenna assembly with mounting bracket
  • Indented Flat 2" square clamp w/ 4 holes
  • 21ft antenna cable
  • Four sets of hex lock-nuts, washers, & bolts

Specifications

  • Hermetically Sealed Antenna
  • Frequency: 2320.0 to 2345.0MHz
  • Satellite Gain: 5dBic Typical / Terrestrial Gain: -1dBic Typical
  • Noise Figure: 1.0dB Max
  • Current Consumption: 45mA Typical/55mA Maximum
  • Supply Voltage: 4.7-Volts Typical
  • Operating Temperature: -40*F to 220*F

Compatible with all satellite radios that features the SMB type antenna connection.



MSTRSAT Universal XM/Sirius Mirror Mount Truck Antenna mstrxm$69.99
SIRXM01 Universal XM/Sirius Mirror Mount Truck AntennaSIRXM01 Universal XM/Sirius Mirror Mount Truck Antenna

This universal satellite radio antenna will work with both XM and Sirius satellite radio receivers ending the need to have two antennas on your vehicle if you listen to both satellite radio services, or change from one to the other. The antenna quickly mounts to any vertical or horizontal tube up to 1-1/10" diameter. For optimal performance, the antenna should be mounted vertically. This extremely versatile antenna can be mounted to any other vehicles such as RV's, off-road vehicles, maritime ships, and motorcycles.

Features:

  • Mirror mount design
  • Works with both XM and Sirius radios
  • Easy installation
  • Replaceable 18ft coax cable
  • Removable elbow SMB adapter
  • Durable, light weight and sleek

Includes:

  • Truck antenna
  • Mirror mount clamp
  • 18ft RG-174 low loss coax cable
  • Removable elbow SMB adapter
  • Hex screws (4)
  • Hex nuts (4)
  • Washers (4)
  • Open ended washers (4)
  • Hex nuts (4)
  • Cable ties (4)

Specifications:

  • Antenna height: 8 inches
  • Dome width: 3 inches
  • Cable length: 18 feet
  • Cable connectors: SMA - SMB

Compatible with all satellite radios that features the SMB type antenna connection.



SIRXM01 Universal XM/Sirius Mirror Mount Truck Antenna sirxm01$39.99
Thru-Glass Mount AntennaThru-Glass Mount Antenna

The Terk TRK-SR1 glass mount satellite radio antenna is a high performance antenna designed specifically for XM Satellite Radio reception. It adheres and transmits signal through your vehicles glass making installation a breeze. The dual functionality allows it to simultaneous receive signals from satellites and terrestrial repeaters to ensure continuous reception. The result is an antenna that offers all the benefits of satellite radio and complements the appearance of any vehicle. The TRK-SR1 must be wired to a 12volt power source.

This antenna features the dual yellow and green antenna connectors. If you will be using this antenna with a dock or receiver that uses the single SMB type antenna connection then you must also use the single antenna adapter. The adapter must be connected from the yellow antenna lead to your receiver.

Warning - while powered, DO NOT directly join the antenna base to the antenna coupler. Doing so without the glass as a spacer will damage your antenna. This type of damage is not covered under warranty.

Features

  • Glass-mounted design uses Terk's exclusive Thru-Glass technology
  • Acrylic foam adhesive pads provide years of worry- free enjoyment, yet are removable if necessary.
  • Shock & vibration proof.
  • Fully adjustable hinged mast can be set to any angel of optimum reception on any surface.
  • Antenna folds down to avoid damage at car washed and other low-clearance situations.
  • XM approved
  • Tested and proven to automotive environmental standards

Includes

  • Antenna
  • Thru-glass Coupler
  • (2) 16' Pre-terminated Micro coaxial cables
  • Installation templates
  • Owners manual
  • (2)Cleaning towelettes
  • Car wash protective sleeve


Thru-Glass Mount Antenna trksr1$49.99
Thru-Glass Single Lead Cable XM AntennaThru-Glass Single Lead Cable XM Antenna

The Think Wireless thru-glass antenna is the first available single lead thru-glass XM antenna. With this antenna you will no longer need to run your antenna cable to the outside of your vehicle. Simply run the interior portion of the antenna from your satellite radio to a window and then adhere the exterior unit to the outside glass and you are ready to go! Signal is transmitted through your vehicles glass making installation a breeze.

Features:

  • Quick and easy installation
  • No wires to run outside your vehicle
  • Adhesive will not damage vehicle
  • XM approved
  • Single cable design
  • Self powered

Includes:

  • Exterior unit
  • Interior unit with cable
  • Alignment template
  • Glass curvature test template
  • Alcohol pads (2)
  • Instruction Manual

Please Note: If you are concerned with installation location and performance, prior to using the antenna's adhesive, you may temporarily adhere the antenna with masking tape over the top of it to test it in your selected mounting location. Do not drive your vehicle unless you have installed the antenna as per the manufacturer's instructions. Once the adhesive is exposed and used, the antenna may not be returned for a refund. Exchange only if defective once the adhesive has been exposed and used.




Availability: Usually ships the same business day

Thru-Glass Single Lead Cable XM Antenna twgl-sr1$59.99
XM Marine AntennaXM Marine Antenna

The XM Marine Antenna is a high-performance antenna, designed to provide crystal-clear XM Radio reception on the water. The antenna installs easily on most boat surfaces and offers options for either deck mounting or mast. It is specifically designed to withstand use in high vibration areas and salt water environments.

Features:

  • Installs easily on most boat surfaces
  • Dual mounting options for deck mount or mast
  • Works with standard 1" -14 thread brackets or antenna mast
  • Designed to withstand the elements of the marine environment
  • Cable can easily be routed through existing access holes

Includes:

  • XM marine antenna
  • Flange mount adapter
  • Pole mount adapter
  • 25-foor antenna cable
  • Flange mount bolts (4)
  • Surface mount screws (4)

Specifications:

  • Antenna dimensions: 3.75 in (w) x 3.75 in (d) x 1 in (h)
  • Antenna weight: 3.7 oz
  • Antenna cable length to connector: 6 in
  • Antenna cable length: 25 ft
  • Flange mount adapter: 4.9 in (w) x 4.9 in (d) x 0.25 in (h)
  • Pole mount adapter: 3.5 in (w) x 3.5 in (d) x 1.5 in (h)

Compatible with standard 1" x 14 thread brackets or antenna mounts (Not Included).




Availability: Usually ships the same business day

XM Marine Antenna marine-antenna$29.99
XMM4 XM Radio Marine AntennaXMM4 XM Radio Marine Antenna

XMM4 Advanced No Ground Plane Antenna For XM Satellite Radio Reception.

Features:

  • The Most Advanced XM Antenna Available.
  • Mounts Anywhere & Meets/Exceeds XM Spec.
  • No Ground Plane Required.
  • Weighs Only Few Ounces.
  • Constructed Of All Marine Grade Materials.
  • Marine Antenna Mount Included.
  • Can Be Used For Other Sat Radio Services (Sirius) with Limited Performance.

Specifications:

Electrical

  • Frequency: 2332.5 to 2345.0 MHz
  • Gain 2 dBic (20-60 deg elevation) -2 dBi (horizon)
  • Bandwidth: 12.5 MHz
  • Impedance: 50 ohms
  • Polarization LHCP (20-60 deg elevation) Linear (Horizon)

LNA

  • Gain: 30 dB, typical
  • Noise Figure: 1.0 dB, maximum
  • Power: 4.5 Vdc, nominal
  • Current Drain: 50 mA, maximum
  • Unwanted Signal Rejection: 35 dB, minimum

Cable

  • Type: Coaxial RG-58A/U
  • Length: 30 feet
  • Connector: SMB

Mechanical

  • Overall Height: 10.25 inches
  • Effective Diameter: 0.75-0.82 inches
  • Housing Material: White ABS, UV Stable
  • Mounting: Fits Standard Marine Antenna Base (Included)
  • Rated Wind Velocity: 100 mph
  • Weight: 0.25 Lbs w/out Cable

Temperature

  • -40 C to +105 C, operating-45 C to +120 C, storage

Quality and Performance Tests

  • XM Approved: Per Specification XM-TEC-3-0009-2-RD

This antenna is compatible all XM Satellite Receivers. NOT compatible with SKYFi car cradles with either a dual-lead connector or a pink Fakra connector.



XMM4 XM Radio Marine Antenna xm-marine-antenna-xmm4$49.99
Terk XM5 Marine AntennaTerk XM5 Marine Antenna

XM Satellite Radio increases the quality of your boating time with over 100 channels of quality programming. Terk's XM5 is a high-performance marine antenna, designed to provide crystal-clear XM Radio reception on the water.

The antenna is tested to withstand extreme environmental conditions - its sealed housing is impervious to damage from salt water or bad weather. The antenna installs using the standard marine mounting bracket, and the 30' cable connects to any XM tuner.

Important Note: You must subscribe to XM Satellite Radio to receive the satellite radio signal. XM satellite radio has an offshore range of at least 100 miles (or more, depending on your location) off the coast of the lower 48 states; service is not available in Alaska or Hawaii.

Kit Includes:

  • XM5 Antenna
  • Mounting Bracket
  • Pink Fakra Adapter
  • 4 Sets of Bolts, Washers, & Nuts
  • 4 Cable Tie Wraps
  • Instruction Manual

Specifications:

  • Frequency: 2332.5 to 2345.0 MHz
  • Gain 2 dBic
  • Bandwidth: 12.5 MHz
  • Impedance: 50 ohms
  • Polarization LHCP (20-60 deg elevation) Omnidirectional
  • Gain: 30 dB, typical
  • Noise Figure: 1.2 dB, maximum
  • Power: 4.5 Vdc, nominal
  • Current Drain: 55 mA, maximum
  • Unwanted Signal Rejection: 25 dB, minimum
  • Cable type: Coaxial
  • Cable length: 30 feet
  • Cable connector: SMB/ Fakra
  • Housing Material: White Polycarbonate
  • Height: 11.75 inches
  • Diameter: 1.88"
  • Rated Wind Velocity: 150 mph
  • Weight: 2.1 Lbs w/out Cable
  • Operating temperature -40 C to +105 C,
  • Storage temperature -45 C to +120 C,

This antenna is compatible all XM Satellite Receivers. NOT compatible with SKYFi car cradles with a dual-lead connector.



Terk XM5 Marine Antenna terk-xm5-marine-antennaRegular price: $99.98Sale price: $69.99Add: 
Delphi SA10100 Marine AntennaDelphi SA10100 Marine Antenna

XM Satellite Radio increases the quality of your boating time with over 170 channels of quality programming. This Delphi Marine Antenna is a high-performance marine antenna, designed to provide crystal-clear XM Radio reception on the water.

The antenna is tested to withstand extreme environmental conditions - its sealed housing is impervious to damage from salt water or bad weather. The antenna installs using the standard marine mounting bracket, and the 20' cable connects to any XM tuner.

Important Note: You must subscribe to XM Satellite Radio to receive the satellite radio signal. XM satellite radio has an offshore range of at least 100 miles (or more, depending on your location) off the coast of the lower 48 states; service is not available in Alaska or Hawaii.

Kit Includes:

  • Delphi Marine Antenna
  • Mounting Bracket
  • 20 Foot Coaxial Cable with SMB/Fakra connector
  • Pink Fakra Adapter
  • 4 Sets of Bolts, Washers, & Nuts
  • 4 Cable Tie Wraps

Specifications:

Electrical

  • Frequency: 2332.5 to 2345.0 MHz
  • Gain 2 dBic
  • Bandwidth: 12.5 MHz
  • Impedance: 50 ohms
  • Polarization LHCP (20-60 deg elevation) Omni-directional

LNA

  • Gain: 30 dB, typical
  • Noise Figure: 1.2 dB, maximum
  • Power: 4.5 Vdc, nominal
  • Current Drain: 55 mA, maximum
  • Unwanted Signal Rejection: 25 dB, minimum

Cable

  • Type: Coaxial
  • Length: 20 feet
  • Connector: SMB/ Fakra

Mechanical

  • Overall Height: 11.75 inches
  • Housing Material: White Polycarbonate
  • Diameter: 1.88"
  • Rated Wind Velocity: 150 mph
  • Weight: 2.1 Lbs w/out Cable

Temperature

  • -40 C to +105 C, operating
  • -45 C to +120 C, storage

This antenna is compatible all XM Satellite Receivers. NOT compatible with SKYFi car cradles with a dual-lead connector.



Delphi SA10100 Marine Antenna delphi-marine-antenna-sa10100$54.99
Terk XMarine AntennaTerk XMarine Antenna

The XMarine antenna is no longer available. The XM Marine Antenna is a similar antenna and is available for purchase.

Love listening to your satellite radio, and want to bring it out on your boat? The XMarine marine satellite antenna is a must have! Don't leave shore without it. The XMarine installs easily on most boat surfaces with dual mounting options for both deck mount or mast. Works with standard 1" -14 thread brackets or antenna mounts (Not Included). It is specifically manufactured for use in high vibration, salt water environments and can be used within temperatures of -40 F to +185 F. Now you can take your XM Satellite radio Anywhere!

Features:

  • Installs easily on most boat surfaces
  • Dual mounting options for deck mount or mast
  • Works with standard 1" -14 thread brackets or antenna mast
  • Cable can easily be routed through existing access holes

Includes:

  • XMarine Antenna
  • Threaded Flange Adapter
  • 25-Foot antenna cable
  • Slotted extension adapter
  • lock washer & hex nut

Specifications:

Electrical

  • Electrical:2320 to 2332.5 Mhz
  • Bandwidth:12.5 Mhz
  • Impedance:50 ohms
  • Gain:33.5 dB, typical
  • Noise Figure: 0.8 dB, maximum

Mechanical

  • Total Height: Deck Mount - 1.08". Mast Mount - 3.13"
  • Max diameter: 3.75" (outside)
  • Coax Cable: 25' RG-174
  • Temperature: -40 F to +185 F(operating)


Terk XMarine Antenna xmarine$59.99
25-Foot Replacement Truck Antenna Cable System25-Foot Replacement Truck Antenna Cable System

For use between truck antennas that have a threaded SMA connector and XM Receiver car cradles with OR without a pink Fakra. A two part system, the 25' cable has a straight male SMB and threaded female SMA connector. The adapter cable has a 90 degree female SMB connector and a pink Fakra.

For use with a standard SMB jack, simply connect the SMB plug on the 25' cable to the Fakra connector on the adapter. For use with a Fakra jack, simply connect the SMB plug on the 25' cable to the 90 degree SMB jack on the adapter.

Compatible truck antennas:

Please note that this cable may possibly reduce the signal reception of the XM signal since there is no amplifier to counter the minor signal loss that the added cable length causes. Plug and unplug this cable only via the metal connectors. DO NOT pull on the cable itself to disconnect.

90-day parts & labor warranty from MyRadioStore.com




Availability: Usually ships the same business day

25-Foot Replacement Truck Antenna Cable System replacement-truck-antenna-cable-sma-smb$24.99
10-Foot Heavy Duty Replacement Truck Antenna Cable10-Foot Heavy Duty Replacement Truck Antenna Cable

For use between truck antennas that have a threaded SMA connector and satellite radio receiver car cradles with SMB antenna connections. This replacement cable is perfect for truck installations where a heavy duty cable is needed. The cable can also be used for other installations that are compatible with these antenna connectors.

Compatible truck antennas:




Availability: Usually ships the same business day

10-Foot Heavy Duty Replacement Truck Antenna Cable sma-smb$29.99
XM Micro Antenna MountXM Micro Antenna Mount

The XM Antenna Mount will work on any vehicle that has "Towing Style" mirrors. It is designed to be installed on the top bar of a mirror and hold a micro magnetic antenna.. It is made of heavy-gauge steel with a black, powder coat finish. Tested to hold up to the elements, it will look great on any truck.

Most trucks these days have fiberglass bodies and will not allow you to mount the antenna to your roofs. This is a great solution for mounting any new micro antenna on a truck!

Click HERE to view the simple installation instructions.

Antenna not included, and shown for illustrative purposes only.



XM Micro Antenna Mount xm-micro-antenna-mount-trucksRegular price: $24.95Sale price: $22.49
Terk Truck Mirror Mount Bracket for Magnetic AntennasTerk Truck Mirror Mount Bracket for Magnetic Antennas

The Terk SRB-MM XM Antenna Mount will work on any vehicle that has "Towing Style" mirrors. It is designed to be installed on the top bar of a mirror and hold a micro magnetic antenna.. It is made of heavy-gauge steel with a clear polished finish. Tested to hold up to the elements, it will look great on any truck.

Most trucks these days have fiberglass bodies and will not allow you to mount the antenna to your roofs. This is a great solution for mounting any new micro antenna on a truck!

This mount comes with wing-nuts allowing for quick attachment and removal from any truck. Also included is some protective plastic cable wrap to help protect the antenna cable from the elements.

Antenna not included and must be purchased separately.



Terk Truck Mirror Mount Bracket for Magnetic Antennas xm-micro-antenna-mount-srb-mm$19.99
Mirror / Clamp Mount For Magnetic AntennasMirror / Clamp Mount For Magnetic Antennas

This metal mirror / clamp mount will allow you to mount your magnetic car antenna to anything that you can attach it to. Its 5x5 inch platform will fit all Sirius magnetic car antenna. Just tighten the clamp onto any location and you instantly have the perfect mount for your magnetic antenna- indoors or outdoors. Each side of the clamp has rubber protective boots so you wont damage your vehicle. Perfect for mounting to your mirrors, bumper, air dam, etc.

Specifications

  • Minimum Mid Clamp Opening - .5 Inches
  • Maximum Mid Clamp Opening - 2 Inches


Mirror / Clamp Mount For Magnetic Antennas miclmoformaa$9.99